BendPak PL-6000DC Page 48 Installation And Operation Manual Download

Page: 48 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Contact an Electrician

Connecting the Lift to the electrical system requires a certified and licensed Electrician.

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable national and local electrical codes.

Important:

The Lift components do not include a Power Disconnect Switch. When you contact
the Electrician advise them that a UL-Listed Power Disconnect rated for 220 VAC,

25 Amps minimum is required.

The Electrician is required to:
•

Install a Power Disconnect Switch

. The Power Disconnect Switch ensures the operator can

quickly and completely interrupt power to the Lift in the event of an electrical fault, emergency

situation or when the Lift is undergoing service. The Disconnect Switch must be installed within

sight and reach of the Lift Operator. Refer to

Install the Power Disconnect Switch

for more

information.

•

Install a Thermal Disconnect

. Ensures the equipment shuts down in the event of an overload

or an overheated motor. Refer to

Install a Thermal Disconnect Switch

for more information.

The motor on the Power Unit is not thermally protected

•

Connect the Power Unit to a 220 VAC power source

. Refer to

Connect to Power

•

Wire the Power Unit Junction Box

. Make the connections in the Junction Box including the

controls to raise and lower the Lift Platform, the Limit Switch, the Lowering Solenoid, and Power

both to and from the Power Disconnect to the Power Unit. Refer to

Wire the Power Unit

Junction Box

for more information.

The Electrician must provide:
•

A UL Approved Power Disconnect Switch and mount the switch on the Lift.

•

A Thermal Disconnect (the power unit’s motor is

not

thermally protected).

•

An appropriately sized cord grip for the Limit Switch wiring and creating an opening in the Power

Unit’s Junction box.

•

Wire of the appropriate gauge for the voltage, current and distance to the Lift. As well as conduit to

protect and route the wiring to the Lift from the Electrical service protected by an appropriate
circuit breaker.

Refer to the

Wiring Diagram

for further Information.

Install the Power Disconnect Switch

⚠

DANGER

All wiring

must

be performed by a licensed, certified Electrician in accordance with

all applicable national and local electrical codes. Do not perform any maintenance

or installation on the Lift without first verifying that main electrical power has been

disconnected from the Lift and cannot be re-energized until all procedures are

complete.

⚠

DANGER

Verify the Lift is resting on a Safety Lock or on the ground

before

performing any

maintenance. Do not work on the Lift if the Safety Locks are not engaged, you

could be injured or killed.

⚠

WARNING

A Power Disconnect Switch is not provided with this equipment.

Summary of Contents for PL-6000DC
























































































Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands

BendPak PL-6000DC, Installation And Operation Manual

Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands