manualshive.com logo in svg

BendPak PL-6000DC, Installation And Operation Manual

Share
Download
BendPak PL-6000DC Installation And Operation Manual Download Page 51

 

PL-6000DC Two Post Parking Lift 

51

 

P/N 5900273 — Rev. A1 — May 2022 

Connect To Power 

Connect the Power Unit to an appropriate Power Source through the Power Disconnect Switch. 
Power for this Lift is 220 VAC, 60 Hz. single phase and should be protected by a 25 Amp fuse or 
circuit breaker. 
Refer to the 

Wiring Diagram

 and 

Control Console Wiring Diagram

 for further information. 

⚠

 

DANGER

 

All wiring 

must

 be performed by a licensed, certified Electrician in accordance with 

all applicable national and local electrical codes. Do not perform any maintenance 

or installation on the Lift without first making sure that main electrical power has 
been disconnected from the Lift and cannot be re-energized until all procedures are 

complete. 

⚠

 

WARNING

  Keep Wiring and Hydraulic Hoses away from sharp edges or pinch points to avoid 

damage. 

Important Electrical Information: 

•

 

Improper electrical installation can damage the Power Unit Motor. This damage is 

not 

covered 

under warranty. 

•

 

Use a separate Circuit Breaker for each Lift Installed. 

•

 

Protect each circuit with a 25 Amp time-delay fuse or circuit breaker. 

To connect the Lift to Power

: 

 

Verify the Power is disconnected and locked out to prevent re-energizing while you work on the 

Lift. 

 

Connect the Main Power Supply wiring to the Power Disconnect Switch just installed using an 

appropriate gauge wire for the voltage, current and length of run. 

 

Route the Power wiring from the Power Disconnect up to the Junction Box on the Power Unit. 

 

Refer to the 

Wiring Diagram 

and

 Control Console Wiring Diagram

 to connect the power 

to the Contactor and Thermal Disconnect, the Solenoid, and Control Console in the Junction Box. 

Wire the Power Unit Junction Box 

The Junction Box houses the wiring and connections for Power, Thermal Overload, Limit Switch, 
Solenoid and the Lift Controls.The Controls on the Console allow the operator to raise and lower 

Vehicles. Refer to the figure above and the 

Wiring Diagram

 and 

Control Console Wiring 

Diagram

 for wiring information. 

⚠

 

DANGER

 

All wiring 

must 

be performed by a licensed, certified Electrician in accordance with 

all applicable national and local electrical codes. 

The Junction Box wiring includes: 

•

 

Power

. Wiring connections for power supplied to the Hydraulic Power Unit from the Power 

Disconnect Switch. 

•

 

Control Console

. This wiring includes the Up, Down and Emergency Stop Lift functions. 

•

 

Limit Switch

. This Switch stops the upward motion of the Lift Platform. 

•

 

Solenoid

. The Solenoid opens the Hydraulic Valve allowing the Lift Platform to Lower. 

Summary of Contents for PL-6000DC

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands