BendPak PL-6000DC Page 45 Installation And Operation Manual Download

Page: 45 / 88

PL-6000DC Two Post Parking Lift

P/N 5900273 — Rev. A1 — May 2022

Connecting the Safety Lock Release Cable

A Wire Rope connects the Safety Lock Release Handle to the Safety Lock Release Mechanism. The

Wire Rope is factory installed and routed from the Release Handle through the Control Arm, around a
Sheave and then up and out of the Control Arm to be attached to the Rocker Arm on the Release

Mechanism. Refer to the figures below.

To Attach the Safety Lock Release Cable

Route the Release Cable from where it exits the Control Arm up to the Rocker Arm on the Release

Mechanism. Refer to the figures below.

Connect the end of the Safety Release Cable from the Control Arm to the Rocker Arm Assembly

on the Safety Lock Release Angle using the Cable Clamp.

Adjust the Safety Release Cable tension using the Wire Rope Clamp until a smooth motion is

achieved on the Safety Release Mechanism, when pulling on the Manual Safety Lock Release

Handle.

Summary of Contents for PL-6000DC
























































































Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands

BendPak PL-6000DC, Installation And Operation Manual

Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands