BendPak PL-6000DC Installation And Operation Manual Download Page 53 | Manualshive

Page: 53 / 88

BendPak PL-6000DC Installation And Operation Manual Download Page 53

PL-6000DC Two Post Parking Lift

53

P/N 5900273 — Rev. A1 — May 2022

Adjusting the Safety Locks and Safety Release

Perform a visual inspection of the Safety Release System as the Lift is moving up and down.

Rotate the two ends of the Adjustable Joint clockwise and counterclockwise to verify that the locks
may be easily unlocked when pulling the Safety Release Handle, and will also engage the Locks

when the Safety Release Handle is released. Refer to the figure below.

Operational Test Two. Run the lift up and down (5) five times while verifying the locks are
engaging/disengaging correctly, that the Lift does not jerk or jump as it runs.

Verify the Hydraulic Fluid level is correct with the Lift on the Ground.

Adjusting the Limit Switch

The Limit Switch will stop the upward motion of the Lift and may be adjusted within the range of the

Limit Switch Arm travel. Adjust the Limit switch, if required. Refer to the figure below.

«
...
51
52
53
54
55
...
»

Summary of Contents for PL-6000DC

























































































Reviews:

No comments