BendPak Clearfloor 10AP Installation And Operation Manual Download Page 64

Page: 64 / 96

10AP Series Two-Post Lifts

P/N 5900265 — Rev. A6 — December 2022

Typical Lifting Points

⚠

WARNING

Before attempting to lift a Vehicle verify:

•

The Vehicle Frame is strong enough to support its weight and has not been weakened or
compromised by modification, damage, or corrosion.

•

The Vehicle individual axle weight does not exceed one-half the Lift capacity.

•

All- Lift Adapters are in secure contact with the Frame at the Vehicle manufacturers’
recommended Lift Points.

•

The Vehicle is stable on the Lift and the center of gravity is not shifted making the Vehicle off
balance.

•

The overhead switch bar will contact the highest point on the Vehicle.

Summary of Contents for Clearfloor 10AP
































































































Search results

Summary of Contents for Clearfloor 10AP

Reviews:

Related manuals for Clearfloor 10AP

Brands by name

Popular brands

BendPak Clearfloor 10AP, Installation And Operation Manual

Search results

Summary of Contents for Clearfloor 10AP

Reviews:

Related manuals for Clearfloor 10AP

Brands by name

Popular brands