manualshive.com logo in svg

BENDIX XVision, Manual

Share
Download
BENDIX XVision Manual Download Page 5

5

Knob kit (service piece no. 5010247) 

–

 

The knob kit

includes four 1/4 in. flat washers and two 1/4-20 threaded
knobs, which are installed onto both sides of the display
when it is mounted in the CB style.

Plastite

®

 screws

 – The CB style mounting kit includes four

#10 Plastite

®

 screws, each 1/2 in. long. Depending on the

chosen CB mount, the screws are used to attach the
mounting brackets to either the headliner or dashboard of
the vehicle.

FRICTION HINGE MOUNTING KIT (PIECE NO.
5010082)

Friction hinge mounting allows the driver to use the sun
visor during the day and the XVision

®

 system at night. The

display pivots on a pair of friction hinges, similar to a vehicle
sun visor. The hinges allow the display to be flipped out of
the way of the visor and latched into either position by use
of a magnet and striker plates.

The friction hinge mounting kit includes the following items.

Hinge Supports

 – Two hinge supports secure the display

to the vehicle headliner when the friction hinge mount is
used. The hinge supports are fastened to the headliner with
four #10 Plastite

®

 pan head screws and to the display with

two M2.5 threadroll pan head screws.

Magnet Kit (piece no. 5010524)

 – The magnet kit includes

a magnet, striker plates, spring, and hardware. The magnet
and spring are attached to the display, and one (1) striker
plate is fastened to the vehicle headliner. The other striker
plates (2) sandwich the sun visor.

Screw and Shim Kit (piece no. 5010249) 

–

 

The screw

and shim kit includes twelve #10 Plastite

®

 pan head screws

and twelve spacer blocks. The screws are used to fasten
the friction hinge supports to the vehicle headliner and are
supplied in three different lengths. The spacer blocks can
be used to level the friction hinge supports, if necessary.
Based on the number of spacers needed to level out the
mount, use either the 1/2 in., 3/4 in., or 1 in. long screws.

CB Style (Overhead)

CB Style (Dashboard)

Mounting Brackets

Mounting Brackets

FIGURE 5 - CB MOUNTING BRACKETS

FIGURE 6 - KNOB KIT COMPONENTS

Knob Kit
Components

Hinge Supports

Magnet Kit
Components

M2.5
Threadroll
Pan Head
Screw

M2.5

Threadroll

Pan Head

Screw

FIGURE 7 - FRICTION HINGE MOUNTING KIT
COMPONENTS

#10 Plastite Pan Head

Screws (Qty. 4)

Summary of Contents for XVision





























Reviews:

No comments

Brands by name

Popular brands

Load more brands