manualshive.com logo in svg

BENDIX XVision, Manual

Share
Download
BENDIX XVision Manual Download Page 17

17

Display Bracket Replacement - CB Style Mount
(Overhead)

Refer to 

CB Style Mount (Dashboard)

 procedure.

Display Bracket Replacement - Friction Hinge
Mount (Visor)

1. Unscrew and disconnect the 25-pin connector of the

display harness.

2. Flip the display down to allow access to the friction

hinge supports.

3. Remove the four #10 Plastite

® 

 pan head screws that

secure the display to the headliner.

4. Remove the two M2.5 threadroll pan head screws that

secure the friction hinge supports to the display.

5. Secure the new friction hinge supports to the display

with the M2.5 threadroll pan head screws.

IMPORTANT:

 Do not exceed 15 in-lbs. when

fastening. If 15 in-lbs. are exceeded, the screw head
will shear off or the stand-offs will strip. The threadroll
screws will form threads in the standoffs as they are
tightened. If it feels as though the screw is binding,
back out the screw slightly and continue to tighten to
prevent breakage.

6. Secure the new friction hinge supports to the headliner

with the four #10 Plastite

®

 pan head screws. Torque the

screws to approximately 15 in-lbs.

7. Reconnect the 25-pin connector of the display harness.

Base Plate 8-32 Mounting

Four 8-32 inserts are provided in the display base.
A template is provided to help guide the drilling
of holes. Use a 13/64 in. bit for drilling the four clearance
holes.  Typically, this installation is used when the display
is being recessed.

FIGURE 30 - WASHERS AND THREADED KNOBS [SHOWN
IN CB STYLE MOUNT (OVERHEAD) POSITION]

Display Bracket Replacement - CB Style Mount
(Dashboard)

1. Unscrew and disconnect the 25-pin connector of the

display harness.

2. Unscrew the threaded knobs from the display and

brackets. Set the display, knobs, and washers aside.
Exercise care to prevent dropping the washers into the
venting on the dash.

3. Remove the four #10 Plastite

® 

pan head screws from the

brackets and dashboard. Set the four screws aside.

4. Secure the replacement brackets with the four 

 

screws

from Step 3.

5. Torque the screws to approximately 20 in-lbs.
6. Slide one of the washers onto one of the threaded knobs.
7. Hold one washer between the display and a bracket while

threading the washer/knob from the outside of the
bracket. See Figure 30.

8. Repeat steps 6 and 7 for the other side of the display.
9. Reconnect the 25-pin connector of the display harness.

Summary of Contents for XVision





























Reviews:

No comments

Brands by name

Popular brands

Load more brands