BENDIX XVision Manual Download Page 25

Page: 25 / 28

Situation

Possible Solutions

IR camera image is not displayed after the
Bendix logo fades away on the display.

Wait two minutes after the XVision

system has been powered to

view the IR camera image.

Check to see if the IR camera window is blocked.

Headlamps were turned off and the XVision

system timed out

(approximately 7 seconds after the headlamps are turned off the
display will turn off.)

Check to see if the IR camera is aimed correctly.

Display image is upside down.

Check that DIP switch 4 is set correctly. Reference figure 14 on
page 8.

Check that DIP switch 3 is set correctly. Reference figure 14 on
page 8.

Check to see if the display intensity is set correctly.

Check that the combiner is open to an angle that allows you to
see the image.

Check to see if the combiner, fold mirror, and LCD are clean.

Check to see if the IR camera window is cracked. Moisture
between the window and lens will limit image quality.

2-pin

Description

Voltage

IR camera heater

+ 12 Volts

power

IR camera heater

ground

power

Display image is reversed, right to left.

The display image is difficult to view.

Check the 2-pin IR camera harness connector is plugged into
the IR camera heater. Reference figure 21 on page 11.

Check that the terminals are seated and the wiring is secure.

Check the 2-pin IR camera harness connections. Reference the
XVision

system schematic, figure 43 on page 23 @ K .

Snow build up on the IR camera window with the
XVision

system powered.

Summary of Contents for XVision




























Search results

Summary of Contents for XVision

Reviews:

Brands by name

Popular brands

BENDIX XVision, Manual

Search results

Summary of Contents for XVision

Reviews:

Brands by name

Popular brands