Belden lumberg automation 934 878-001 Technical Manual Download Page 22

Page: 22 / 75

4.3 Port Assignments

4 Assembly and Wiring

Attention:

For modules with a 7/8" housing, use the "SELV and

Limited Energy" power source.

4.3.3 Power Supply with M12 Power L-Coded

Color coding: gray

Figure 6: Schematic diagram of the M12 L-coding (connector), port X03 (IN)

Figure 7: Schematic diagram of the M12 L-coding (socket), port X04 (OUT)

Power supply Pin

Signal

Function

(+24 V)

System/sensors

GND_U

Actuator

GND_U

System/sensors

(+24 V)

Actuator

Function earth

Table 4: Assignment of X03, X04

Attention:

Only use power supply units for the system/sensor

and actuator supply that correspond to PELV (Protective Extra

Low Voltage) or SELV (Safety Extra Low Voltage). Power supplies

according to EN 61558-2-6 (transformers) or EN 60950-1 (switching

power supply units) fulfill these requirements.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Summary of Contents for lumberg automation 934 878-001












































































Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands

Belden lumberg automation 934 878-001, Technical Manual

Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands