Belden lumberg automation 934 878-001 Technical Manual Download Page 21

Page: 21 / 75

4 Assembly and Wiring

4.3 Port Assignments

Figure 4: Schematic drawing, port X03 (IN)

Figure 5: Schematic drawing, port X04 (OUT)

Port

Pin

Signal

Function

Power supply

GND_U

Actuator

X03, X04

GND_U

System/sensors

Functional earth

(+24 V)

System/sensors

(+24 V)

Actuator

Table 3: Assignment of ports X03, X04

Attention:

For the input module 0980 ESL 301-xxx, the two contacts 1

and 5 are not required for the power supply to the actuators. However,

these two contacts are connected to each other on the connector and

socket side to enable 5-pin transmission of the power supply to a

downstream module.

Attention:

Only use power supply units for the system/sensor

and actuator supply that correspond to PELV (Protective Extra

Low Voltage) or SELV (Safety Extra Low Voltage). Power supplies

according to EN 61558-2-6 (transformers) or EN 60950-1 (switching

power supply units) fulfill these requirements.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Summary of Contents for lumberg automation 934 878-001












































































Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands

Belden lumberg automation 934 878-001, Technical Manual

Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands