Belden lumberg automation 934 878-001 Technical Manual Download Page 71

Page: 71 / 75

9 Technical Data

9.4 Power Supply for the Actuators

Nominal voltage U

24 V DC (SELV/PELV)

Voltage range

18-30 V DC

Electric isolation

Yes

Threshold value of the undervoltage detection

Typ. 17 V

Delay time for

undervoltage detection

< 20 ms

Reverse polarity protection

Yes

Operational indicator (U

)

Green LED, 18 V <= U

+/- 1 V <= 30 V

Red LED, U

< 18 V +/- 1 V or U

> 30 V +/- 1 V

Table 34: Information on the power supply for the actuators

Attention:

The reverse polarity protection only works if the supply

of the actuators is protected with an overcurrent fuse (10 A, mT) and

switched off upon short-circuit within 10 to 100 ms at the latest.

Warning:

In case of polarity reversal, a power supply unit with current

regulation or an incorrect fuse will lead to destruction of the module.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Summary of Contents for lumberg automation 934 878-001












































































Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands

Belden lumberg automation 934 878-001, Technical Manual

Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands