Belden lumberg automation 934 878-001 Technical Manual Download Page 60

Page: 60 / 75

8.2 Configuration Page (Config)

8 Integrated Web Server

8.2.1 Firmware Update for PROFINET

Requirements

PC with network interface

Web browser (e.g.

www.mozilla.org

)

Performing Update

Reset into delivery status by setting the address switch to 979 and by

running a power restart of the module. A period of 10 seconds should be

waited (during the restart procedure the red BF/MS LED flashes on and

off cyclically three times until the restart is completed / The 1st step is only

necessary if the module was already operated on a PLC).

Set the IP address on the PC network interface (e.g. 192.168.001.050,

different from the IO module).

Set the IP address on the IO module using a configuration tool (e.g.

Hilscher Config Tool) over DCP to 192.168.001.001 and run a power

restart of the module.

Open the WEB page

http://192.168.1.1

in the browser.

Select

Config

tab on WEB page.

Select and click the

Firmware Update

button.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Summary of Contents for lumberg automation 934 878-001












































































Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands

Belden lumberg automation 934 878-001, Technical Manual

Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands