Belden lumberg automation 934 878-001 Technical Manual Download Page 53

Page: 53 / 75

7 Diagnostic Properties of the

Modules

7.7 Alarm and Error Messages of

LioN-P/-R Modules via PROFINET

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Byte 3

X4-B

X4-A

X3-B

X3-A

X2-B

X2-A

X1-B

X1-A

Byte 4

X8-B

X8-A

X7-B

X7-A

X6-B

X6-A

X5-B

X5-A

Table 30: Bit assignment for the 16DI/DO modules

7.6.5 Key

LV-U

: Undervoltage of sensor supply U

LV-U

: Undervoltage of actuator supply U

SC: Sensor short-circuit

AC: Actuator short-circuit

FM: Force Mode activated

IME: Internal module error

X1...X8: M12 slot with diagnostics

X1-A...X8-A: M12 slot, channel A

X1-B...X8-B: M12 slot, channel B

7.7 Alarm and Error Messages of LioN-P/-R

Modules via PROFINET

Attention:

Alarm and error messages are only transmitted via

PROFINET when the parameter for diagnostics is activated in the

configuration of the modules in the controller.

If the LioN-P modules detect an error condition, an alarm message will be

triggered. The modules support diagnostic alarms. Diagnostic alarms are

triggered in case of peripheral faults such as overload, short-circuit, and

undervoltage.
An alarm is triggered in case of an incoming event (such as sensor short-

circuit) as well as an outgoing event.
The evaluation of the alarms depends on the PROFINET I/O controller used.

Technical Manual LioN-P PROFINET

Version 2.0 10/2017

Summary of Contents for lumberg automation 934 878-001












































































Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands

Belden lumberg automation 934 878-001, Technical Manual

Search results

Summary of Contents for lumberg automation 934 878-001

Reviews:

Related manuals for lumberg automation 934 878-001

Brands by name

Popular brands