Belarus 1021 Operating Manual Download Page 34 | Manualshive

Page: 34 / 209

Belarus 1021 Operating Manual Download Page 34

BELARUS-1021/1021.3

Operating manual

33

3.5 Gearbox control

With single lever control, the gears are

shifted by the lever (1) in accordance with the
shifting pattern. Before engaging a gear, use
the lever (1) to select the desired range.

Important!

Ranges and gears are engaged

by the single lever (1), first the range is
selected (I-st or II-nd), then the lever is
shifted to the “N” position and the desired
gear is selected.

Important!

The 4th gear can only be engaged

when the II-nd range is selected.

The multiplier lever (2) must be in the ON

position: forward — slow gear (L) or
backward — overdrive gear (H).

Note:

The multiplier (accelerator) lever is

fixed in its extreme positions. The multiplier
lever can be shifted to its neutral position to
facilitate start of the engine during cold
season.

Your tractor can be equipped with two-

lever GB control

Ranges and gears are shifted by individual

levers (1) and (2), as shown on the charts on
the left-side figure.

First use the lever (2) to engage a range (I-

st or II-nd), then use the lever (1) to engage
the required gear.

Important!

With two-lever GB control, the

4th gear can only be engaged when the II-
nd range is selected.

Important!

The 4th gear can only be engaged

when the II-nd range is selected.

3.6 Speed reducer control (if installed)

«
...
32
33
34
35
36
...
»

Summary of Contents for 1021


















































































































































































































Reviews:

No comments