manualshive.com logo in svg

Belarus 1021, Operating Manual

The Time Electronics 1021 Technical Manual is an essential resource for users looking to optimize their experience with our high-quality product. Easily download this comprehensive manual for free from our website, providing clear instructions and technical specifications to enhance your understanding and maximize benefits from the Time Electronics 1021.

Share
Download
background image

BELARUS-1021/1021.3

Operating manual

136

Trouble, its manifestation

Remedy

4. Noise at maximum turn angle of wheels

Incorrect FDA operation mode. FDA

operates in positive engagement mode.

Check the FDA drive engagement mode and

set the switch to OFF or Automatic

Incorrect limit wheel turn angle of steerable

wheels.

Check and adjust the FDA reducer turn angle

as described in 5.6 FDA adjustments of this
Manual.

5. Knocking in pivot during motion

Maladjusted pivot bearings

Check and adjust axial preload in pivot

bearings as described in 5.6 FDA adjustments
of this Manual.

6. Knocking in FDA at a sharp turn of wheels

Plays in pins of the steering rods and turn

cylinders.

Check and adjust.

7. Lubricant leak through the flange cup of the final drive driving pinion

Worn or damaged flange cup.

Replace the worn out parts.

8. Lubricant leak through the yoke cup of the double universal joint

Worn or damaged cup

Replace the cup

9. Lubricant leak through the cup of the wheel reducer driving pinion

Increased play in the pinion bearings.

Check and adjust axial play in driving pinion

bearings as described in 5.6 FDA adjustments
of this Manual.

Worn or damaged cup.

Replace the cup.

10. Lubricant leak through the wheel flange cup

Axial play in the bearings of the flange.

Adjust wheel flange bearings as described in

5.6 FDA adjustments of this Manual.

Worn or damaged cup.

Replace the cup.

11. Lubricant leak through wheel reducer breathers

High oil level.

Check and set the correct level.

Summary of Contents for 1021


















































































































































































































Reviews:

No comments

Related manuals for 1021

Kubota 77700-12652 Installation Manual preview
77700-12652
Brand: Kubota Pages: 11
Kubota B1710 Workshop Manual preview
B1710
Brand: Kubota Pages: 370
New Holland TD5010 Service Manual preview
TD5010
Brand: New Holland Pages: 41
LS CS18-007 Adjustment Manual preview
CS18-007
Brand: LS Pages: 11
ryan GA 30 544885 Operator'S & Parts Manual preview
GA 30 544885
Brand: ryan Pages: 67
Kalmar DCF100-45E7 Operator'S Manual preview
DCF100-45E7
Brand: Kalmar Pages: 88
Walker DM36-2 Illustrated Parts Manual preview
DM36-2
Brand: Walker Pages: 32
GE MONOGRAM ZCG3100 BB Owner'S Manual preview
MONOGRAM ZCG3100 BB
Brand: GE Pages: 12
Toro 72086 Operator'S Manual preview
72086
Brand: Toro Pages: 44
New Holland LS35-16H Operator'S Manual preview
LS35-16H
Brand: New Holland Pages: 36
New Holland HCCZ7240CFCP38297 Service Manual preview
HCCZ7240CFCP38297
Brand: New Holland Pages: 51
LS tractor LL4100 Operator'S Manual preview
LL4100
Brand: LS tractor Pages: 46
LS tractor LL2100 Operator'S Manual preview
LL2100
Brand: LS tractor Pages: 46
LS tractor LB3100 Operator'S Manual preview
LB3100
Brand: LS tractor Pages: 61
LS tractor LB1100 Series Operator'S Manual preview
LB1100 Series
Brand: LS tractor Pages: 64
LS tractor J2020H Operator'S Manual preview
J2020H
Brand: LS tractor Pages: 101
LS tractor R4041 Operator'S Manual preview
R4041
Brand: LS tractor Pages: 125
LS tractor J2023H Operator'S Manual preview
J2023H
Brand: LS tractor Pages: 113

Brands by name

Popular brands

Load more brands