manualshive.com logo in svg

Belarus 1021, Operating Manual

Share
Download
Belarus 1021 Operating Manual Download Page 171

BELARUS-1021/1021.3

Operating manual

170

1 — adjusting bolt; 2 — right brake pedal lever; 3,4 — lever; 5 — pin; 6 — fork; 7 —

locknut; 8 — parking brake control lever.

Fig. 8.4.35 – Adjust parking-reserve brake control (with lever)

Adjust the parking-reserve brake control (option with a rod located under operator’s

left hand) as follows:

Link the rod (3) (Fig. 8.4.36) of the extension mechanism (2) with the lever (5) and cotter it

with the pin (8); rotating the nuts (4) ensure alignment of the upper edges A of the arm holes (9)
and (10), then lock the nuts (4).

Adjust the travel of the lever (1) with the screw (6) so that under an effort (300 ± 10) N on

the lever (1) its travel be 110 to 120 mm, then tighten up the nut (7).

Set the switch VK-409 so that shifting the lever (1) of the extension mechanism (2)

to its lowest position ensure opening of the electrical circuit of the parking brake lamp,
and shifting it to the first tooth of the rod close of the circuit.

Perform final adjustment of the parking brake on an assembled tractor. The tractor must

be held on a slope (18±3)%. If necessary, re-adjust using the bolt (6).

200

+10

 N

Summary of Contents for 1021


















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands