Beijing TT Aviation Technology Co., Ltd. TIANNONG M6E User Instructions Download Page 3

Page: 3 / 45

Catalogue

1.Use Instruction

...............................................................................................................................

1.1 Safety Instruction

...............................................................................................................

1.2 Pesticide Usage

.................................................................................................................

1.3 Inspection

............................................................................................................................

1.4 Environment

........................................................................................................................

1.5 Operation

.............................................................................................................................

1.6 Compass Calibration Requirements

...............................................................................

2. Product Introduction

.....................................................................................................................

2.1 TIANNONG M6E Parameter

............................................................................................

2.2 TIANNONG M6E Agriculture UAV Specification

..........................................................

2.3 Preparation Before Takeoff

............................................................................................

2.3.1 Installation of the Fuselage,water tank and landing gear.

.............................

2.3.2 Arm Installation

.....................................................................................................

2.4.3 Spraying Tube Installation

..................................................................................

2.3.4 Intelligent Battery Installation

.............................................................................

3.Intelligent Battery Instruction

.....................................................................................................

3.1 Keypad Function

..............................................................................................................

3.2 Electricity Inspection

........................................................................................................

3.3 Lifetime Inspection

...........................................................................................................

3.4 Charging

............................................................................................................................

3.5 Reminding Functions

......................................................................................................

3.5.1 Maintenance Reminder

.......................................................................................

3.5.2 Low Voltage Alarm

...............................................................................................

3.5.3 Storage Reminder

................................................................................................

3.6 Self Balance and Self Storage in Storage

...................................................................

4.Charger Station Introduction

.....................................................................................................

4.1 Production Parameters

...................................................................................................

4.2 Wiring diagram

.................................................................................................................

4.4 Product Function Feature

...............................................................................................

4.5 Operation Instruction

.......................................................................................................

5. App Setting of Copter

................................................................................................................

5.1 Software Configuration

...................................................................................................

5.1.1 Multicopter Type

...................................................................................................

5.1.2 Transmitter Calibration

........................................................................................

5.1.4 Compass

................................................................................................................

5.1.4.1 Calibration Command

..............................................................................

5.1.5 Sensitivity Settings

...............................................................................................

5.1.5.1 Basic Sensitivity

.....................................................................................

5.1.5.2 Control Sensitivity

.....................................................................................

5.1.5.3 Other Parameters

.....................................................................................

5.1.6 Low Voltage Protection

........................................................................................

5.1.6.1 Settings of Low Voltage Protection

........................................................

Summary of Contents for TIANNONG M6E












































Search results

Summary of Contents for TIANNONG M6E

Reviews:

Related manuals for TIANNONG M6E

Brands by name

Popular brands

Beijing TT Aviation Technology Co., Ltd. TIANNONG M6E, User Instructions

Search results

Summary of Contents for TIANNONG M6E

Reviews:

Related manuals for TIANNONG M6E

Brands by name

Popular brands