Beijing TT Aviation Technology Co., Ltd. TIANNONG M6E User Instructions Download Page 29 | Manualshive

Page: 29 / 45

background image

Copyright © 2017 TTAAll Rights Reserved.

Appendix Implication of indicator light

28

Calibration has been done before it leave factory,it is not recommended to calibrate by
user to avoid calibration error.

Calibration is recommended to be done if temperature difference between last calibration
is too big.

5.1.4 Compass

5.1.4.1 Calibration Command

1) Calibration mode begins when click “calibration start”.

2)

Compass calibration mode starts when SA of transmitter goes back and forth more

than 4 times.

5.1.4.2 Calibration step

1) Confirm GCS communication well, compass installation correct and copter outside.

2) Clicking calibration, yellow LED of copter is on, hold and keep copter rotating

clockwise and slowly, leave copter head to the ground when green led is on, rotate

copter clockwise and slowly till LED flash in red,green and yellow alternately.

3) After vertical calibration,calibration mode will be exited automatically and LED will

«
...
27
28
29
30
31
...
»

Summary of Contents for TIANNONG M6E














































Reviews:

No comments

Related manuals for TIANNONG M6E

Brand: Walkera Pages: 26

Brand: WORLD TECH ELITE Pages: 16

Brand: World Tech Toys Pages: 16

Brand: BluEye Pages: 44

Brand: Cocoon Pages: 20

Brand: emesent Pages: 154

Brand: Rage Pages: 12

Brand: XAG Pages: 28

Brand: Catalyst Pages: 74

Brand: AirDroids Pages: 25

Brand: Airdog Pages: 75

Brand: Airdog Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands