Beckhoff AG2250 Operating Instructions Manual Download

Page: 72 / 95

Scope of supply

───

Version: 2.8

AG2250

Check the scope of supply for missing or damaged parts

Check your delivery for completeness. If any parts are missing or
became damaged during transport, contact the carrier, vendor or
our service department immediately.

Check the shipment for the following contents:

• Gear units from the AG2250 series with packaging

• Short information

Screws for fastening the gear unit to the motor or the machine are
not included in the scope of delivery .

No motor is included in the standard delivery of a planetary gear unit
from the AG2250 series.

5.1

Packaging

Instructions for handling are printed on the packaging:

Symbol

Explanation

This is the correct position for the packaging.

The packaging must be protected from moisture.

The contents are fragile.

Summary of Contents for AG2250
































































































Search results

Summary of Contents for AG2250

Reviews:

Related manuals for AG2250

Brands by name

Popular brands

Beckhoff AG2250, Operating Instructions Manual

Search results

Summary of Contents for AG2250

Reviews:

Related manuals for AG2250

Brands by name

Popular brands