background image

 

www.bdsensors.de

 

ASM 400 

4.2 Menu operation 

The menu system is a closed system allowing you to scroll both forward and backward through 
the individual set-up menus to navigate to the desired setting item. All settings are permanently 
stored  in  an  EEPROM  and  therefore  available  again even  after disconnecting from  the  supply 
voltage. The menu system and the menu items have been designed as simply as possible. Be-
low, each individual menu item is described in detail allowing a straightforward and quick confi-
guration of your device. The structure of the menu system is identical for devices with or without 
contacts. The device with contacts deviates from the one without contacts by ten or five addi-
tional menus. These additional menus are marked by a gray background for clear identification.  

 

Please  follow  the  manual  meticulously  and  remember  that  changes  of  the  adjustable 

 

parameters  (switch-on  point,  switch-off  point,  etc.)  become  only  effective  after  pushing 

 

both buttons simultaneously and leaving the menu item. 

4.3 Password system 

The device is equipped with an access protection to allow access to the complete menu system 
only to authorized persons. 

  Activating the access protection with the password will lock the complete menu. 

  Deactivating the access protection with the password will unlock the complete menu. 

 

The password can be activated and deactivated through menu "PAon" resp. "PAof". 

 

It can be changed according to special menu 4. 

 

In  case  the  password  has  been  lost,  there  is  a  possibility  to  reset  the  password. 

 

You can do this by loading the defaults via the special menu 3. 

4.4 Unit 

The  unit  of  the  values  to  be  measured  is  determined  on  ordering.  But  it  is  also  possible  to 
change the unit later by using one of the enclosed unit labels. 

Summary of Contents for ASM 400





















Reviews: