baxter Flo-Gard 6201 Operator'S Manual Download Page 42

Technical Specifications

ITEM

SPECIFICATION

Catalog Code Number

2M8063

Description

Linear Peristaltic Volumetric Infusion Pump

Administration Set

Baxter “s” designated sets

Keep Vein Open (KVO)
Rate

5 mL/hr or programmed rate, whichever is less

Nurse Call

Available through the

COMMUNICATIONS PORT.

Battery

12 Volt, 2.0 Ah sealed lead-acid

Battery Life

Approximately 6 hours with pump running at a rate
from 1 to 1400 mL/hr

Battery Recharge

8 hours for more than 80% recharge

AC Power Requirements

110/120V, 60 Hz

Power Cord

2.9 m (9.5 ft) long, with Hospital Grade plug

Fuse

0.5 A, 250V, SB, 5.2 mm (

13

64

in)

×

20 mm (

25

32

in)

Leakage Current

Less than 50 microamps (using UL-544 specified test
methods)

Weight

Approximately 5.3 kg (11.6 lbs)

Dimensions

20 cm W

×

13 cm D

×

29 cm H (7.9" W

×

5.1" D

×

11.4" H)

Flow Rate Range

Primary program: 1.0–99.9 mL/hr in 0.1 mL increments
or 1–1999 mL/hr in 1 mL increments. Upper limit can be
reduced by authorized service personnel.
Secondary program: 1.0–99.9 mL/hr in 0.1 mL incre-
ments or 1–999 mL/hr in 1 mL increments

VTBI Range

1.0–99.9 mL in 0.1 mL increments or 1–9999 mL in 1 mL
increments for both primary and secondary. Upper limit
can be reduced by authorized service personnel.

38

Rev.B

Summary of Contents for Flo-Gard 6201





















































Reviews: