Baxi 946 Installer'S Manual Download Page 43

Page: 43 / 43

Refit the hotbox as described in the relevant installation

sections. Make sure gas soundness, sealing, spillage test
and performance are satisfactory.

17.9 To remove the Quantum fascia.

Remove the firefront.

Remove the two screws securing the bottom of the

fascia to the sides of the hotbox (See figure 69).

Carefully lift the fascia upward to clear the upper

retaining bracket on the hotbox (See figure 70). Pull the
fascia clear and place carefully aside.

Refit in the reverse order. Make sure that the fascia is

properly located over the upper retaining bracket.
See section 14 of this manual for detailed fitting
instructions.

17.10 To remove the Camden, Fusion and Coast
fascia.

Remove the firefront.

The fascia is made up of three trims. These trims

are held in place by magnets. Remove the top trim
by pulling forward. Place carefully aside (See figure
71).

Remove the side trims by pulling forward.

Place carefully aside (See figure 71).

Refit in the reverse order. Make sure that the

top corners of the fascia have no gaps.

Page 43

INSTALLER GUIDE

Figure 71. Removal of fascia

Figure 70. Quantum fascia
removal

Figure 69. Removing the
fascia securing screws

Summary of Contents for 946












































Search results

Summary of Contents for 946

Reviews:

Related manuals for 946

Brands by name

Popular brands

Baxi 946, Installer'S Manual

Search results

Summary of Contents for 946

Reviews:

Related manuals for 946

Brands by name

Popular brands