Baur PD-TaD 80 User Manual Download Page 70

Page: 70 / 74

Index

PD-TaD 80

70 / 74

822-188-3

About this manual

• 6

Accessories and spare parts

• 62

Anti-corona protection

• 68

Applicable documents

• 6

Available methods

• 14

Avoiding dangers, taking safety
measures

• 10

Cable testing and dissipation factor
measurement

• 53

Calibrator

• 20

Change of the dissipation factor
between successive steps

• 68

Checks to perform before
commissioning

• 31

Cleaning the PD-TaD 80 and system
components

• 60

Connecting the HF filter to the PD-
TaD 80

• 48

Connecting the HF filter with a
connection piece

• 48

Connecting the HF filter without a
connection piece

• 48

Connecting the PD-TaD in the cable
test van

• 35, 40

Connecting the system

• 30

Connecting the system for dissipation
factor measurement

• 40

Connecting the system for PD
measurement

• 35

Connecting the system to the PHG
70/80 portable VLF HV generator

•

37, 44

Connecting the system to the supply
voltage

• 49

Connection cables

• 22

Connection point (near end)

• 68

Connection set

• 19

Connection with an HV connection
cable with MC plug

• 49

Dangers when working with high
voltage

• 11

Declaration of conformity

• 67

Delivery scope and options

• 66

Discharging

• 57

Discharging and earthing the test
object

• 56

Disposal

• 66

Dissipation factor, dielectric
dissipation factor

• 68

Earth system

• 34

Earthing

• 58

Ensuring there is no voltage at the
work place

• 32

Evaluation of partial discharge testing
• 55

Far end

• 68

Faults and corrective measures

• 63

For your safety

• 9

Full illustration of the PD-TaD and
system components (PD-TaD 80 as
a standalone system)

• 15

Guaranteeing immediate measures
in an emergency

• 12

HF filter

• 19

NDEX

Summary of Contents for PD-TaD 80











































































Search results

Summary of Contents for PD-TaD 80

Reviews:

Baur PD-TaD 80, User Manual, Page: 70 / 74

Search results

Summary of Contents for PD-TaD 80

Reviews: