Baur PD-TaD 80 User Manual Download Page 14

Page: 14 / 74

Product information

PD-TaD 80

14 / 74

822-188-3

3.1

Available methods

Measurements using the following methods are possible with the PD-TaD 80:

Method

Description

Required VLF HV
generator

Partial discharge
testing

Is used to identify and locate PD activities in the cable
insulation

PHG 70 / PHG 80

PHG 70 portable /
PHG 80 portable /
viola

VLF cable testing with
parallel partial
discharge testing

Is used for:



VLF cable testing



Identify and locate PD activities in the cable insulation

With this method, the cable testing and partial discharge
testing are carried out simultaneously.

PHG 70 / PHG 80

PHG 70 portable /
PHG 80 portable /
viola

Dissipation factor
measurement

Is used for:



Evaluation of the dielectric condition of the insulation



Indication of PD, water trees, humidity in joints, etc.

PHG 70 TD /
PHG 80 TD

PHG 70 portable /
PHG 80 portable /
viola TD

RODUCT INFORM ATION

Summary of Contents for PD-TaD 80











































































Search results

Summary of Contents for PD-TaD 80

Reviews:

Baur PD-TaD 80, User Manual, Page: 14 / 74

Search results

Summary of Contents for PD-TaD 80

Reviews: