manualshive.com logo in svg

Baur PD-TaD 80, User Manual, Page: 51 / 74

Share
Download
Baur PD-TaD 80 User Manual Download Page 51

 

 

PD-TaD 80 

Preparing a measurement 

822-188-3 

51 / 74 

7.1 

Switching on the system and starting the BAUR software 

1.  Switch on the system. 

Further information: User manual for the cable test van or the VLF HV generator 

The system status changes to the 

Ready for operation

 operating state. 

2.  The PD measuring unit of the PD-TaD 80 will be switched on automatically when it is 

supplied with voltage. Wait until all the LEDs on the PD-TaD 80 display the ready for 
operation status.   

 

PWR

 

– green 

 

PD

 

– orange 

     

 

     

3.  Start the BAUR software 4. 

The Dashboard opens.   

     

 

  For information on performing the diagnostics methods, refer to the 

user manuals for the BAUR software 4. 

         

 

7.2 

Selecting a cable route and entering cable data 

     

 

  For information on selecting or entering cable data, refer to the 

user manual for the BAUR software 4. 

     

 

7 

P

REPARING A MEASUREME NT

 

Summary of Contents for PD-TaD 80











































































Reviews:

No comments