Baur PD-TaD 80 User Manual Download Page 34

 

 

Connecting the system 

PD-TaD 80 

34 / 74 

822-188-3 

Note:

 The tension belts are not included in the PD-TaD 80 standard delivery. 

 

6.7 

Points to note during connection 

The following factors are crucial for precise measurement results: 

 

Short connections   

 

Protective earthing cable should be a flat copper strip (standard delivery) 

 

Maximum possible distance between the connection cables and the adjacent system 
components not to be tested   

 

Keep the HV coupling unit of the PD-TaD 80 and the terminations clean and dry 

 

No current loops in the power supply 

 

6.8 

Use of the anti-corona protection 

To achieve measurement results that are as precise as possible, we recommend using the 
anti-corona protection device. Corona discharges on sharp edges in a test setup may cause 
a high noise level. The anti-corona hoods included within the standard delivery protect 
sharp-edged parts in order to prevent corona discharges affecting the measurement result. 

 

6.9 

Earth system 

Note:

All the necessary connection cables and connecting elements are included in the 

standard delivery. 

1.  A 16 mm

2

 protective earthing cable is included in the standard delivery of the   

PD-TaD 80. Use this cable to connect the protective earthing connection of the   
PD-TaD 80 to the station earth (directly on the test object screen). 

Important: 

To keep the antenna effect to a minimum and thus prevent interference, the 

protective earthing cable must be a flat copper strip which is kept as short as possible. 

2.  PD-TaD 80 integrated in the cable test van: Earth the cable test van. Follow the 

instructions in the user manual for the cable test van. 

PD-TaD 80 as a standalone system: Earth the VLF HV generator. Follow the user 
manual for the VLF HV generator in question. 

3.  A short-circuit cable is secured to the earthing terminal on the PD-TaD 80. Connect this 

short-circuit cable to the 

HV IN

 and 

HV OUT

 ports. 

4.  If you are using a VLF HV generator with a 50 m long HV connection cable, connect the 

screen (operational earthing) of the HV connection cable to the 

Screen (HV Cable)

 port 

of the PD-TaD 80. 

 

Summary of Contents for PD-TaD 80











































































Reviews: