Baumuller BM4-O-IEI-01 Operating Instructions Manual Download Page 24

Page: 24 / 92

Assembly

Operating Instructions Option Module IEI for b maXX drive PLC BM4-O-IEI-01
Document No.: 5.02013.02

Baumüller Nürnberg GmbH

of 90

5.4

Pull the cover forward from the controller section: you can now see the slots.

Look for the intended slot (

) on the controller section.

Figure 7:

Assembly

Turn the spagnolet locks above and below this slot by 90°. The spagnolet locks are
now horizontal.

Take out the front panel cover forward. Keep this cover. If you remove plug-in cards,
you must close the unit again using the cover.

Observe the described ESD measures when handling the modules.

Remove the IEI option module from the transportation packaging: Avoid contact with
the plug-in module's electronic components.

DANGER

The following

will occur

if you do not observe this danger information:

serious personal injury

death

Danger from:

electricity.

The unit and the vicinity of the control cabinet may carry dangerous

voltages.

Before starting any work, ensure that the unit and its vicinity are free of voltage. Observe the
relevant safety regulations when handling current-carrying units.

CAUTION

The following

may occur

if you do not observe this caution information:

property damage.

Danger from:

electrostatic discharge.

The

IEI-01

ncremental encoder interface contains

ESD components.

Observe the described ESD measures when handling the plug-in module.

Only hold the plug-in module by the gripping piece (see "C" in

Figure 5

on page 22).

Summary of Contents for BM4-O-IEI-01





























































































Search results

Summary of Contents for BM4-O-IEI-01

Reviews:

Baumuller BM4-O-IEI-01, Operating Instructions Manual, Page: 24 / 92

Search results

Summary of Contents for BM4-O-IEI-01

Reviews: