manualshive.com logo in svg

Baumuller BM4-O-IEI-01, Operating Instructions Manual, Page: 11 / 92

Share
Download
Baumuller BM4-O-IEI-01 Operating Instructions Manual Download Page 11

Basic Safety Instructions

Operating Instructions Option Module IEI for b maXX drive PLC BM4-O-

IEI-01

11

of 90

2

2.2

Information signs

2.3

Legal information

This documentation is intended for technically qualified personnel that has been specially 
trained and is completely familiar with all warnings and maintenance measures. 

The equipment is manufactured to the state of the art and is safe in operation. It can be 
put into operation and function without problems if you ensure that the information in the 
documentation is complied with.

Operators are responsible for carrying out servicing and commissioning in accordance 
with the safety regulations, applicable standards and any and all other relevant national 
or local regulations with regard to cable rating and protection, grounding, isolators, over-
current protection, etc.

Operators are legally responsible for any damage that occurs during assembly or connec-
tion.

2.4

Appropriate Use

You must always use the plug-in module appropriately. Some important information is list-
ed below. The information below should give you an idea of what is meant by appropriate 
use of the plug-in module. The information below has no claim to being complete; always 
observe all the information that is given in these operating instructions.

m

You must only install the plug-in module in series b maXX 4400 units.

m

Configure the application such that the plug-in module is always operating within its 
specifications.

m

Ensure that only qualified personnel works with this plug-in module.

m

Mount the plug-in module only in the specified slot/slots.

m

Install the plug-in module as specified in this documentation.

m

Ensure that connections always comply with the stipulated specifications.

m

Operate the plug-in module only when it is in technically perfect condition.

m

Always operate the plug-in module in an environment that is specified in the technical 
data.

m

Always operate the plug-in module in a standard condition. 

 

For safety reasons, you must not make any changes to the plug-in module.

m

Observe all the information on this topic if you intend to store the plug-in module.

You will be using the plug-in module in an appropriate way if you observe all the com-
ments and information in these operating instructions.

NOTE

This indicates particularly important information.

Summary of Contents for BM4-O-IEI-01





























































































Reviews:

No comments