Baumfolder BAUM 2018 Instruction Manual Download Page 14

Page: 14 / 50

TP10313

PAGE 14

2.1.3 Machine Setup Parameters

Table 3. Machine Setup Parameter List

P20: Units of Measurement

This selection specifies the unit of measurement used to

display all lengths. Inches (SAE) is the default selection.

Available choices are Meters (measurement displayed in cm)

and Inches (measurement displayed in inches and tenths of

inches).

P21: Language

This selection specifies the Language used to display

fault messages. Available choices are ENGLISH,

DEUTSCH, and CODES, see Tables 1618, Error Message
Translation. English is the default selection.

P22: Network Address

This selection specifies the unit address used for

Network communication. Available choices are 0 through

255. Address 0 is the default selection. Network functions

are not available in software version 2.6.0

P23: Pause

P24: Network Enable

Network components must be installed and enabled in

Maintenance Mode. Enable Network by selecting 1.

Disable network by selecting 0.

Function

Type

Variable

Displayed

P20

Units of Measure

Setup Variables

Adjustable

Inches, Meters

P21

Language

Setup Variables

Adjustable

English, German, Codes

P22

Network Address

Setup Variables

Adjustable

0-255

P23

Pause

Setup Variables

Adjustable

1 or 0

P24

Network

Setup Variables

Adjustable

1 or 0

P25

Easy

Setup Variables

Adjustable

1 or 0

P26

Software Version

Machine Configuration

Fixed

V X.X.X

P27

Machine Type

Machine Configuration

Fixed

Set at Factory

P28

Serial Output Type

Machine Configuration

Fixed

Off, Display, or Network

P25: Easy Mode

Enable Easy Mode by selecting 1. Disable Easy Mode

by selecting 0.

Easy Mode has two sheet control methods, Easy setup or

Continuous cycle. Easy setup will run any job with a 1 inch

sheet gap. The sheet gap display contains 3 dashes and the

Suction Length bar graph is turned off.

In Continuous cycle setup, the suction cycle is determined by

the sheet gap setting, sheet length setting and the suction

length setting. Sheet error detection methods are turned off.

P26: Hardware and Firmware Version

This selection shows the hardware and firmware

versions of the unit. The left side of the display shows logic

board type. The right side of the display shows the firmware

version (2.X.X).

P27: Machine Type

This selection, in maintenance mode, shows the selected

machine configuration.

P28: Serial Output Type

This selection, in maintenance mode, shows selected

serial output type.

Summary of Contents for BAUM 2018



















































Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands

Baumfolder BAUM 2018, Instruction Manual

Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands