Baumfolder BAUM 2018 Instruction Manual Download Page 20

Page: 20 / 50

TP10313

PAGE 20

Reset Function

Pressing and holding this key will result in a reset

function being activated after a 5-second countdown. The

function is based on the current large display selection, see

table 12. The large display (1) will show countdown to

reset in this manner. When the button is pressed the

message CLr In 5 will show on the large display (1). At

one second intervals the display will progress through CLr

In 4, CLr In 3, CLr In 2, CLr In 1, and finally will

show CLEArEd when the reset action is complete.

Reset while showing Output Count will reset all job
variables.

Reset while showing batch data will reset Number
of Batches and reload the Batch Down Count.

Reference Name

Description

Designator

LED1

Tachometer Indicator

Tracks the Tachometer input.

LED2

Not Used

Turns on when MKE output is activated.

LED3

Suction Indicator

Tracks the Suction output.

LED4

Status of Relay K1

LED5

Pile Down

Tracks the Pile down output.

LED6

Pile Up

Tracks the Pile up output.

LED7

Pile Indicator

Tracks the Pile outputs. If one of the Pile

outputs is on, this LED will be on.

LED8

Logic +5VDC Supply

Shows status of Logic +5VDC Supply

LED9

Is5VDC Supply

Shows status of Is5VDC Supply

LED10

Is24VDC Supply

Shows status of Is24VDC Supply

LED11

Kicker

Turns on when kicker output is activated.

Table 14. LED Status Indicators

3.0 Logic Board Status Indicators

Several of the controller functions are monitored with

LED indicators located on the Logic Board (see Table 14).

The status of all other inputs are shown on the 8 Digit

display in Machine Setup mode (see Tables 1 - 6).

Table 13. Reset mode Selection

Summary of Contents for BAUM 2018



















































Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands

Baumfolder BAUM 2018, Instruction Manual

Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands