Baumfolder BAUM 2018 Instruction Manual Download Page 16

Page: 16 / 50

TP10313

PAGE 16

2.1.6 Machine UsageStatus Parameters

Table 6. Machine Usage Status Parameter List

P50: Power On Time

This selection shows the time in 1/100 hour during the

main switch of the machine is on.

P51: Machine Run Time

This selection shows the time in 1/100 hour during the

main drive contactor of the machine is on.

P52: Total Input Sheets

This selection shows the total input counts in 1000

sheets

Exit Machine Setup and Diagnostic Mode

Pressing any of these keys will cause the controller to

change to a new mode.

2.2 Counter Setup Mode

Pushing this key puts the counter in counter setup

mode.

Counter setup mode is used to prepare the controller to

run a job. The large display (1) shows the batch preset on

the left-hand side and the batching output time on the right

hand side. The decimal points in the large display (1) will

move from side to side to indicate that a parameter may be

changed. The small display (2) shows the batching type. The

suction length display (3) is active.

Change Batching Type

The minus and plus buttons move through a list of four

output devices. The chosen Type is then activated when the

batch down-count goes to zero. Feed interruption stops the

feeding of sheets for the batching time setting.

Function

Type

Variable Displayed

P50

Power on time

Machine Status

Based on Inputs

Time in 1/100 Hours

P51

Machine run time

Machine Status

Based on Inputs

Time in 1/100 Hours

P52

Total Input Sheets

Machine Status

Based on Inputs

Number in 1000 Sheets

The speed up-table output activates the marking table

output for the batching time duration.

The MKE mode is an unavailable option.

The kicker is a future feature.

The output types are represented by animated symbols.

The sequence of frames for the animations is shown in
table 7.

Table 7. Output Type Animations

Batch Preset Adjustment

These buttons cause the batch preset value to increment or

decrement. The preset will be reloaded after the user leaves

the setup mode only if the value has been changed.

Feed Interruption

Speed Up Table

MKE Table

Kicker

Frame

Not

Available

Future

Feature

Summary of Contents for BAUM 2018



















































Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands

Baumfolder BAUM 2018, Instruction Manual

Search results

Summary of Contents for BAUM 2018

Reviews:

Related manuals for BAUM 2018

Brands by name

Popular brands