manualshive.com logo in svg

Baroness LM315GC, Owner'S Operating Manual, Page: 78 / 86

Share
Download
Baroness LM315GC Owner'S Operating Manual Download Page 78

Press the middle of the belt with your finger
to check the belt tension.

1

i352yo-001

Engine Tension Belt_001

1

Engine tension belt

Loosen the nut to adjust the length of the
spring is 50.0 mm (1.969 in).

1

A

A

i352yo-004

Engine Tension Belt_002

1

Nut

A

50.0 mm (1.969 in)

Lock it with the nut.

Adjustment of Parking Brake

Danger

Danger

If the brake wire is cut, the machine will be
unable to stop. This would be extremely
dangerous.
If the brake wire is cracked or damaged,
replace it with a new one immediately.
If the parking brake is not sufficiently effective
when it has been applied, adjust the brake
wire.

3.

4.

5.

Adjust the parking brake by tightening the
brake wire adjustment bolt.

1

2

4

3

ulabms-003

Adjustment of Parking Brake_001

1

Parking brake lever

2

Lock nut

3

Adjustment bolt

4

Brake wire

Adjusting Work Speed

Follow the steps below to make adjustments.

( - #30420)

Set the reel rotation switch to the "MOW"
(reel rotation) position.

1

B

A

mh4pyw-006

Adjusting Work Speed_001

1

Reel rotation switch

A

Rotate

B

Stop

Loosen the locknut on the side of the reel
rotation switch to adjust the length of the
bolt.

Length of the bolt (Longer): Slower
Length of the bolt (Shorter): Faster

1.

2.

･
･

LM315GC

Maintenance

Page 5-16

Maintenance (Main Body)

Summary of Contents for LM315GC























































































Reviews:

No comments