manualshive.com logo in svg

Baroness LM315GC, Owner'S Operating Manual, Page: 54 / 86

Share
Download
Baroness LM315GC Owner'S Operating Manual Download Page 54

( - #30420)

1

1dndt8-002

Up Switch_001

(#30421 - #30726)

3

WD

2

WD

MOW

TRAVEL

1

1dndt8-005

Up Switch_002

1

Up switch

2WD/3WD Selector Switch

Caution

When switching between 2WD and 3WD
operation, make sure to stop the machine
completely.

Caution

In case of 2WD/3WD model, travel in 2WD
mode since it is dangerous to travel on steep
downward slopes, wet road surface or
downward slopes of wet lawn in 3WD mode.
Rear tire going into a skid may cause loss of
traveling control.

Important

When the reel rotation switch is set to the
"MOW" (reel rotation) position, regardless of
the position of the 2WD/3WD selector switch,
3WD is selected.
When the traveling mode is switched to 3WD,
the red LED in front of the 2WD/3WD selector
switch lights up.

Note:
Depending on the specifications, this function
may not be available.
The 2WD/3WD selector switch is located in the
operation panel.

When the switch is set to the "2WD" position,
the machine will be in two-wheel drive. When
it is set to the "3WD" position, the machine
will be in three-wheel drive.
When the traveling mode is switched to
3WD, the red LED in front of the 2WD/3WD
selector switch lights up.
( - #30420)

A

B

1

ofo39l-005

2WD/3WD Selector Switch_001

(#30421 - )

B

A

A

1

ofo39l-006

2WD/3WD Selector Switch_002

1

2WD/3WD selector switch

A

3WD

B

2WD

LM315GC

Handling Instructions

Page 4-30

Operation of Each Section

Summary of Contents for LM315GC























































































Reviews:

No comments