Baroness LM315GC Owner'S Operating Manual Download Page 23

Page: 23 / 86

K 4 2 0 9 0 0 0 9 8 0

qigqnx-020

K4209000980
Hydraulic oil icon
Read the Owner's Operating Manual.

qigqnx-040

K4209001310
Decal, lead-free gasoline
Use lead-free gasoline.

qigqnx-074

K4205001920
Decal for caution to hot parts

Caution

High temperature - Do not touch. Otherwise, you will
get burned.

qigqnx-012

K4205001910
Decal, caution to getting entangled

Danger

Watch for rotating parts - Keep your hands away
from the belts while the engine is running.

SLOW

qigqnx-059

K4205002040
Decal, caution to sloped land

Danger

Rollover - Do not work on slopes of 15 degrees or
more.
When you descend a slope, drive at low speed.
If the machine is equipped with ROPS, fasten your
seatbelt.

qigqnx-060

K4205002050
Decal, caution to exhaust gas diffusion

Warning

Caution to exhaust gas diffusion - All persons other
than the operator must keep a safe distance from the
machine.

Product Overview

LM315GC

Product Overview

Page 3-7

Safety Signs and Instruction Signs

Summary of Contents for LM315GC























































































Search results

Summary of Contents for LM315GC

Reviews:

Baroness LM315GC, Owner'S Operating Manual, Page: 23 / 86

Search results

Summary of Contents for LM315GC

Reviews: