manualshive.com logo in svg

Baroness LM315GC, Owner'S Operating Manual, Page: 77 / 86

Share
Download
Baroness LM315GC Owner'S Operating Manual Download Page 77

1

Wire

2

Bolt A

3

Bolt B

4

Brake shoe Assy

5

Brake drum

Remove the bolts.

1

75uxaw-005

Rear Tires_004

1

Bolt

Remove the tire from the wheel mounting
base.

Caution

Refer to the Tightening Torque Table.
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

Important

Tighten the bolts in the tightening order
(crosswise).

For installing the rear tires, reverse the
removing procedure.

Adjustment of Belt Tension

Caution

Be sure to stop the engine before adjusting
the belts.

Important

Make sure that the belt has the specified
amount of tension.

If the belt becomes slack due to frequent use, it
may jump or slip.

7.

8.

In addition, if it is overtightened, it may wear
prematurely.
If necessary, adjust it, and always check the
belt for appropriate tension.

Reel Cutter Drive Belt

Caution

Be sure to stop the engine before adjusting
the belts.

Tilt the underseat cover forward and open
the cover.
Open the hood.
Press the middle of the belt with your finger
to check the belt tension.
If the belt is too slack, loosen the bolts and
move the flexible wire housing (the pulley
attached) with the spanner to adjust the
tension.

Adjust belt tension so that the deflection may
be 13±2 mm when applying 5.5 kgf load right
in the middle of pulleys.

2

3

1

eqhyge-001

Reel Cutter Drive Belt_001

1

Reel cutter drive belt

2

Bolt

3

Flexible wire housing

Engine Tension Belt

Caution

Be sure to stop the engine before adjusting
the belts.

Tilt the underseat cover forward and open
the cover.
Open the hood.

1.

2.
3.

4.

1.

2.

Maintenance

LM315GC

Maintenance

Page 5-15

Maintenance (Main Body)

Summary of Contents for LM315GC























































































Reviews:

No comments