5
•
Do not use direct or high pressure water jets or steam clea-
ners to clean the appliance.
• Do not use corrosive products to clean the floor or shelf be
-
neath the appliance.
• Do not wash the body or flame spreader of the hob burners
in the dishwasher.
3 SAFETY AND CONTROL DEVICES
ELECTRIC OVEN
SAFETY THERMOSTAT
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
•
The appliance is equipped with a manual reset safety ther-
mostat which interrupts heating when the operating tempera-
ture exceeds the maximum permitted value.
•
To restore appliance operation, remove the control panel (the
front panel for Boiling pans and Bratt pans) and press the
thermostat reset button. This procedure must only be carried
out by a qualified, authorized technician.
SOLID TOP RANGE HOB
If the red light (next to the yellow one) on the control panel
comes on, this indicates a fan malfunction: switch the applian-
ce off as quickly as possible and call the technical assistance
service. This indicator light comes on when the thermal fuse
trips. The thermal fuse must be replaced together with the fan.
4 DISPOSAL OF PACKAGING AND THE APPLIANCE
PACKAGING
The packaging is made using environmentally friendly mate-
rials. The plastic recyclable components are:
•
the transparent cover, the bags containing the instructions
manual and nozzles ( made of polyethylene - PE.).
•
the straps (in polypropylene - PP).
APPLIANCE
The appliance is manufactured 90% from recyclable metals
(stainless steel, aluminum sheet, copper.... ).
The appliance must be scrapped in compliance with current
regulations governing such disposal.
•
It must be disposed of properly.
•
Make the appliance unusable before scrapping.
5 RISKS DUE TO NOISE
•
As regards airborne acoustical noise emissions, the A-
weighted sound pressure level is below 70 dB(A).
INSTRUCTIONS FOR INSTALLATION
REMINDERS FOR THE INSTALLER
The manufacturer will not be liable for any damage or in-
jury resulting from failure to observe the following rules.
•
Read this manual carefully. It provides important information
for safe installation, use and maintenance of the appliance.
• Installation, conversion to a different type of gas and applian
-
ce maintenance must be carried out by qualified technicians
authorized by the manufacturer, in compliance with current
safety standards and the instructions given in this manual.
• Identify the specific appliance model. The model number is
detailed on the packaging and on the appliance data plate.
•
The appliance must be installed in a well-ventilated room.
•
Do not obstruct any air vents or drains present on the ap-
pliance.
•
Do not tamper with appliance components.
6 REFERENCE STANDARDS AND LAWS
Install the appliance in compliance with current safety regula-
tions.
Install the appliance in compliance with current regulations.
7 HANDLING
The packaging is marked with warning symbols that indicate
the precautions to be taken when handling the appliance to
avoid damage.The appliance must only be handledusing su-
itable equipment. If lifting equipment is used, such as forklift
trucks or similar, make sure that the appliance is in a stable
position.
8 UNPACKING
Check the state of the packaging and in the event of damage,
ask the delivery person to inspect the goods.
•
Remove the packaging.
• Remove the protective film from the exterior and interior pa
-
nels. Use a suitable solvent to remove any residual adhesive
from the panels.
9 POSITIONING
•
The overall dimensions of the appliance and the position of
connections are given on the installation diagram at the start
of this manual.
•
The appliance can be installed singly or in combination with
other appliances in the same product range.
•
The appliance is not suitable for integrated installation.
•
Position the appliance at least 10 cm from adjacent walls.
This distance can be reduced in the presence of non-combu-
stible or heat-insulated walls.
•
Level the appliance by means of the height-adjustable feet.
•
Where installed singly, the countertop appliance weighing
less than 40kg must be secured using the flanged feet pro
-
vided.
APPLIANCE ASSEMBLY WITH BASE, BRIDGE, AND CAN-
TILEVER SOLUTIONS
Follow the instructions provided with the type of support utili-
zed.
FIXING THE APPLIANCE TO THE FLOOR
Appliances of 40cms in width installed alone must be fixed to
the floor. Use the flanged feet provided.
JOINING APPLIANCES TOGETHER IN LINE
• Pull out the control knobs , remove control panel.
• Place the appliances side by side and adjust the tops to the
same height.
•
Unite the appliances using the screws.
