Barnstead Thermolyne Corporation EASYpure RF 1051 Series Operation Manual And Parts List Download | Manualshive

Page: 17 / 28

background image

17

7.

Disconnect the membrane switch lead from the
printed circuit board. (See Figure 6.)

8.

Disconnect the resistivity cell lead from the printed
circuit board.

9.

Disconnect the printed circuit board relay plug by
squeezing the retaining clip while pulling the plug
straight out from the frame.

10. Remove the nuts holding the printed circuit board in

place.

11. Remove the printed circuit board. Disconnect power

supply (3 wires) from printed circuit board.

12. Reconnect power supply to new printed circuit

board and install the new printed circuit board.
Refer to electrical diagrams.

13. Reconnect the resistivity cell lead and printed circuit

board relay plug.

14. Reconnect the membrane switch lead.

15. Reinstall the front cover.

16. Retape the Luer fitting with new Teflon

®

tape and

reinstall fitting.

17. Reinstall the EASYpure RF’s cover.

18. Reconnect the power cord to the unit and the unit

to the power supply.

M

AINTENANCE AND

S

ERVICING

«
...
15
16
17
18
19
...
»

Summary of Contents for EASYpure RF 1051 Series





























Reviews:

No comments

Related manuals for EASYpure RF 1051 Series

Brand: ParaBody Pages: 4

Brand: YSI Pages: 70

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: Rainbow Pages: 18

Brand: CAMAG Pages: 40

Brand: ICP DAS USA Pages: 45

Ransomes HR 6010

Brand: Jacobsen Pages: 10

Brand: Jacto Pages: 64

Brand: Konica Minolta Pages: 32

Brand: laerdal Pages: 9

Brand: Saadat Pages: 61

Brand: Saadat Pages: 22

Brand: zapco Pages: 14

Brand: Crosley Pages: 6

Brand: Gambro Pages: 273

SimNewB Anomaly Set

Brand: laerdal Pages: 10

MIDORI ULB-50sc

Brand: Ushio Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands