background image

4

Warnings

WARNING

A.  To avoid electrical shock, always:

1. Use a properly grounded electrical outlet of correct voltage and current handling capacity.
2. Do not place the EASYpure RF directly over equipment that requires electrical service. Routine main-

tenance of this unit may involve water spillage and subsequent electrical shock hazard if improperly
located.

3. Replace fuses with those of the same type and rating.
4. Do not disassemble water lines or remove cartridges where spilled water could contact equipment

that requires electrical service. Disassembly of water lines and removal of cartridges will result in
water spillage. Electrical shock hazard could result.

5. Disconnect from the power supply prior to maintenance and servicing.

B.  To avoid personal injury:

1. Do not use in the presence of flammable or combustible materials; fire or explosion may result. This

device contains components which may ignite such materials.

2. This device is to be used with water feeds only. Sanitizing/cleaning agents must be used in compli-

ance with instructions in this manual. Failure to comply with the above could result in explosion and
personal injury.

3. Avoid splashing disinfecting solutions on clothing or skin. 
4. Ensure all piping connections are tight to avoid chemical leakage. 
5. Carefully follow manufacturer’s safety instructions on labels of chemical containers and material safe-

ty data sheets.

6. Refer servicing to qualified personnel.

Summary of Contents for EASYpure RF 1051 Series





























Reviews: