background image

Version 1.25

   |   E3 IP66 Outdoor Rated User Guide   |   

9

www.bardac.com

Mains switch-disconnector Lock Off

On the switched models the mains switch-disconnector can be locked in the ‘Off’ position using a 20mm standard shackle padlock 
(not supplied).

IP66 / NEMA 4X Unit Lock Off

3.6. Removing the Terminal Cover

To access the connection terminals, the drive front cover needs to be removed as shown.

IP66 / NEMA 4X Units

Removing the screws on the front of the product allows access to the connection terminals, as shown below.

3.7. Routine Maintenance

The drive should be included within the scheduled maintenance program so that the installation maintains a suitable operating 
environment, this should include:

  

Ambient temperature is at or below that set out in section 

10.1. Environmental on page 54

.

  

Heat sink fans (where fitted) freely rotating and dust free.

  

The Enclosure in which the drive is installed should be free from dust and condensation; furthermore ventilation fans and air filters 
should be checked for correct air flow.

Checks should also be made on all electrical connections, ensuring screw terminals are correctly torqued; and that power cables 
have no signs of heat damage.

Mech

anical Installation

3

Summary of Contents for E3 Series































































Reviews: