background image

56

   |   E3 IP66 Outdoor Rated User Guide   |   

Version 1.25

www.bardac.com

Supply Voltage

200 – 240 RMS Volts for 230 Volt rated units, + /- 10% variation allowed. 240 Volt RMS Maximum.
380 – 480 Volts for 400 Volt rated units, + / - 10% variation allowed, Maximum 500 Volts RMS.

Frequency

50 – 60Hz + / - 5% Variation

Short Circuit Capacity

Please refer to 

10.2. Input Power Supply Requirements

 for maximum supply short-circuit capacity limits.

Limits apply as shorct-circuit Amperes symmetrical with the specified maximum supply voltage when protected by UL type 

J fuses.

Mechanical Installation Requirements

All E3 drive units are intended for installation within controlled environments which meet the condition limits shown  in section 

10.1. Environmental

.

The drive can be operated within an ambient temperature range as stated in section 

10.1. Environmental

.

Electrical Installation Requirements

Incoming power supply connection must be according to section 

4.4. Incoming Power Connection

.

Suitable power and motor cables should be selected according to the data shown in section 

10.3. Rating Tables

 and the National Electrical Code 

or other applicable local codes.
Motor Cable

75°C Copper must be used.

Power cable connections and tightening torques are shown in section 

3.3. Mechanical Dimensions

.

Integral Solid Sate short circuit protection does not provide branch circuit protection. Branch circuit protection must be provided in accordance with 

the national electrical code and any additional local codes. Ratings are shown in section 

10.3. Rating Tables

.

For installations in Canada transient surge suppression must be installed on the line side of this equipment and shall be rated 480Volt (phase to 

ground), 480 Volt (phase to phase), suitable for over voltage category iii and shall provide protection for a rated impulse withstand voltage peak 

of 2.5kV.
UL Listed ring terminals / lugs must be used for all bus bar and grounding connections.

General Requirements

E3 drive provides motor overload protection, set at 150% of full load, in accordance with the National Electrical Code (US).
Where a motor thermistor is not fitted, or not utilised, Thermal Overload Memory Retention must be enabled by setting P-60 = 1.
Where a motor thermistor is fitted and connected to the drive, connection must be carried out according to the information shown section 

4.11.2. 

Motor Thermistor Connection

.

UL rated ingress protection (“Type” ) is only met when cables are installed using a UL recognized bushing or fitting for a flexible conduit system 

which meets the required level of protection (“Type”).
For conduit installations the conduit entry holes require standard opening to the required sizes specified per the NEC.
Not intended for installation using rigid conduit system.

WARNING:

 The opening of the branch-circuit protective device may be an indication that a fault has been interrupted. To reduce the risk of fire 

or electric shock, current-carrying parts and other components of the controller should be examined and replaced if damaged. If burnout of the 

current element of an overload relay occurs, the complete overload relay must be replaced.

ATTENTION:

 Le déclenchement du dispositif de protection du circuit de dérivation peut être dû à une coupure qui résulte d’un courant de 

défaut. Pour limiter le risque d’incendie ou de choc électrique, examiner les pièces porteuses de courant et les autres éléments du contrôleur et les 

remplacer s’ils sont endommagés. En cas de grillage de l’élément traversé par le courant dans un relais de surcharge, le relais tout entier doit être 

remplacé.

10.6. EMC Filter Disconnect

Drives with an EMC filter have an inherently higher leakage current to Ground (Earth). For applications where tripping occurs the 
EMC filter can be disconnected by completely removing the EMC screw on the side of the product.

Remove the screw as indicated right.

The E3 drive product range has input supply voltage surge suppression components fitted to protect the drive from line voltage 
transients, typically originating from lightning strikes or switching of high power equipment on the same supply.
No flash test should be performed on the drive.

Tr

oublesh

ooting

11

Summary of Contents for E3 Series































































Reviews: