manualshive.com logo in svg

Bardac E3 Series, User Manual

Share
Download
Bardac E3 Series User Manual Download Page 11

Version 1.25

   |   E3 IP66 Outdoor Rated User Guide   |   

11

www.bardac.com

4.2. Connection Diagram

All power terminal locations are marked directly on the product. DC+/BR/DC- terminals are not available on Size 1 models. 

4.2.1. IP66 (Nema 4X) Non-Switched Units

L1/L   L2/N    L3

L1/L   L2/N    L3

Mains (1 or 3 phase)

U       V        W

E3 IP66 (NEMA 4X) Non-Switched

PE

BR

DC

+

PE

WI

VI

UI

M

DC

-

Incoming Power Connection  

Additional information in section 

4.4.

 on page 13

Protective Earth PE Connection  

Additional information in section 

4.3.

 on page 13

Isolator/Disconnect 

Ensure there is at least 30 seconds  

between each power-on!

Fuses/Circuit Breaker  

Additional information in section 

4.4.2.

 on page 13

External Line Reactor (optional) 

Additional information in section 

4.4.3.

 on page 14

It must not be used with frame size 4 models!

External EMC Filter (optional) 

Additional information in section 

4.12.

 on page 18

External Output Filter (optional)

 

Output Choke (load reactor)

 

dV/dT filter

 

Sinewave filter

Brake Resistor with Thermal Overload Protection 

Additional information in section 

4.13.

 on page 19

Shielded Motor Cable with PE Connection 

Additional information in section 

4.5.

 on page14

Power & Contr

ol Wiring

4

Summary of Contents for E3 Series































































Reviews:

No comments

Brands by name

Popular brands

Load more brands