9. Communication Module R763768
This unit contains two seven segment led display (E), four normal LEDs (A..D) and an IR receiver (F). The display is used to show
the status of the projector for instance the selected input number, error codes, ….
The four normal leds each have a specific function:
•
IR received (red) (C): Infrared signal or local keypad signal is detected (any address)
•
IR accepted (green) (B): Infrared signal is accepted (own address)
•
Sync detected (yellow) (A): There is a stable sync present on the selected input
•
Power (red/green) (D): red is projector standby, green is projector active
The IR receiver can accept RC5 code. It is positioned next to the display in order to receive the IR signal through the same red glass
as the display.
On board connector pin assignment
Connector J300 - to Communication Interface
Pin Name
Pin No
In/out
Definition
Signal
L_YEL
1
Out
Signal for yellow led (sync present)
TTL
GND
2
Out
Ground
L_IR_OK
3
Out
Signal for green led (IR accepted)
TTL
L_IR_REC
4
Out
Signal for red led (IR received)
TTL
L_PWR_ON
5
Out
Signal for standby led (power on/off)
TTL
SCL_ERROR
6
Out
I2C SCL signal to error display
TTL
SDA_ERROR
7
Out
I2C SDA signal to error display
TTL
IR_DISPLAY
8
In
RC5 signal from IR receiver on display unit
TTL
++5V
9
Out
Power supply
+5V
9.5.3
Error List on INFO display Only
Overview
The following error codes are shown on the two seven segment led display:
Info
Display
Error
Error Description
- c
I
2
C ERROR SCL Line
The I
2
C SCL line doesn’t react (held down), so no I
2
C communication
is possible.
- d
I
2
C ERROR SDA Line
The I
2
C SDL line doesn’t react (held down), so no I
2
C communication
is possible.
- H
"Hardware" ERROR
Indicates an error concerning the hardware. This can be:
•
incompatible hardware found
•
hardware failure
- L
"Lamp" ERROR
Indicates an error concerning the lamp. This can be:
•
an error concerning the LPS
•
an error on the lamp info module
If it concerns an error on the lamp info module, "Wrong Lamp
Parameter(s) is displayed on the LCD display.
- P
SMPS ERROR
Indicates an error concerning the SMPS.
- t
Temperature ERROR
Projector has been shut down due to temperature reasons. This can
be:
•
DMD temperature is out of range.
R5976820 SLM R12+ PERFORMER 08/03/2005
65
Summary of Contents for SLM R12 Plus
