Barco HDX 4K User Manual Download Page 104

Page: 104 / 107

Glossary

The "plane of sharp focus" can be changed so that any plane can be brought into sharp focus. When the DMD plane and lens plane
are parallel, the plane of sharp focus will also be parallel to these two planes. If, however, the lens plane is tilted with respect to the
DMD plane, the plane of sharp focus will also be tilted according to geometrical and optical properties. The DMD plane, the principal
lens plane and the sharp focus plane will intersect in a line below the projector for downward lens tilt.

Subnet mask

A number that is used to identify a subnetwork so that IP addresses can be shared on a local area network.

TR (Throw Ratio)

The ratio of the distance to the screen (throw) to the screen width.

100

R5906070 HDX 4K 23/09/2016

Summary of Contents for HDX 4K












































































































Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands

Barco HDX 4K, User Manual

Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands