Barco HDX 4K User Manual Download Page 70

Page: 70 / 107

10. GUI – Installation

Image 10-10
Warp menu, 4Corners

The 4Corners menu is displayed.

Image 10-11
4Corners Warping

3. To enable warping, make sure the

Enable

slider is set active.

4. To set warping on one or more of the four corners, select one of the four corners.

5. Set the desired X and Y coordinates for this corner.

6. Repeat steps 4 and 5 for each corner, until all corners are warped in the desired position.

10.4 Lamp illumination

What can be done?

Within a certain power mode, the light output of the lamp can be reduced by reducing the lamp power

How to reduce the power

1. In the main menu, select

Installation

→

Illumination

Image 10-12
Installation menu, Illumination

2. In the Illumination Menu, select

Power

R5906070 HDX 4K 23/09/2016

Summary of Contents for HDX 4K












































































































Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands

Barco HDX 4K, User Manual

Search results

Summary of Contents for HDX 4K

Reviews:

Related manuals for HDX 4K

Brands by name

Popular brands