background image

Contents

Overview -

 Components .......................................................................................1

Section 1 -

  Removing Shipping Brackets 

(Tab-Tensioned, "V" Surfaces only)

 .......2

PLEASE READ -

 Safety Information ....................................................................2

Section 2 -

 Hanging Screen .................................................................................3

Section 3 -

 Bottom Access XL Panel Installation/Removal ...........................3

Section 4 -

 Motorized Roller/Fabric Installation ..............................................4

Section 5 -

 Motorized Roller/Fabric Removal ...................................................4

Section 6 -

 Operation............................................................................................5

Section 7 -

 Tab-Tension Adjustment Procedure ..............................................5

Section 8 -

 Limit Adjustments .............................................................................6

Section 9 -

 Case Length Dimensions .................................................................7

Section 10 -

 Case Width Dimensions .................................................................7

Section 11 -

 Mounting Bracket Dimensions......................................................7

Section 12 -

 Wiring Diagrams 110-120V Motor and Quiet Motor ...................8

Overview -

 Components

 CAUTION 

Read and understand all warnings 

(Page 2)

 before beginning installation.

Electrical

Cutout

Tab Tensioning

“V” Dowel

“E” Dowel

Mounting Bracket

Mounting Bracket

Hoisting Bracket

Leveling Brackets

Hoisting Bracket

“E” Free Hanging 

Viewing Surface

“V” Flexible Vinyl 

Viewing Surface

Trim Flange

Shipping Brackets Attached  
to Dowel and Screen Case  

(V Screens Only)

Please Note:

 Shipping brackets must remain 

in place until product has been mounted and 

connected to power 

(see Sections 1 and 4 in this 

document.)

 

Also, DO NOT operate screen before removing 

shipping brackets from screen case.

TOOLS REQUIRED

POWER DRILL

PENCIL

TAPE MEASURE

HARDWARE

 (by others) 

LEVEL

Draper, Inc.  |  411 S. Pearl St. Spiceland, IN 47385 

draperinc.com  |  765.987.7999  |  800.238.7999  

© 2021 All Rights Reserved 

FORM: AccessXL_Inst20

Access XL E and V

Extra large, ceiling-recessed electric screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difficulties installing or servicing your  

Access XL screen, call your dealer or Draper, Inc. 

Summary of Contents for Access XL E Series









Reviews: