Barco DP2K-E series User And Installation Manual Download Page 130

Page: 130 / 163

16. Removal and installation of the projector covers

16.6 Removal of the top cover plate of the Light Processor compartment

To access the top cover plate of the Light Processor compartment the projector top cover has to be removed

rst. This procedure assumes that the projector top cover is already removed.

AUTION

Opening the Light Processor compartment by removing the top cover plate or side cover plate will

result in a tamper event. An authorization to clear the security warning on the projector, after closing off the
Light Processor compartment, will be needed!

Necessary tools

3mm Allen wrench.

How to remove the top cover plate from the Light Processor compartment?

1. Remove the seven screws (reference 1, image 16-7) of the top cover plate. Use a 3 mm Allen key.

Image 16-7

2. Grip the 2 handles (reference 2, image 16-8) and slide the cover towards the front of the projector until the 8 cover latches

(reference 3, image 16-8) are free.

Image 16-8

3. Remove the top cover plate.

126

R5906693 DP2K-E SERIES 19/06/2015

Summary of Contents for DP2K-E series




































































































































































Search results

Summary of Contents for DP2K-E series

Reviews:

Related manuals for DP2K-E series

Brands by name

Popular brands

Barco DP2K-E series, User And Installation Manual

Search results

Summary of Contents for DP2K-E series

Reviews:

Related manuals for DP2K-E series

Brands by name

Popular brands