Barco DP2K-E series User And Installation Manual Download Page 31

Page: 31 / 163

5. Physical installation

5.2

Connecting the projector with the power net

ARNING

The total electrical installation should be protected by an appropriate rated and readily accessi-

ble disconnect switch, circuit breakers and ground fault current interrupters. The installation shall be done
according to the local electrical installation codes.

AUTION

The cross-sectional area of the conductors in the Power Supply Cord shall be not less than 1mm

(18AWG).

Necessary tools

No tools.

Necessary parts

Power supply cord 1mm

(18AWG), min. 300V with IEC 60320 - C13 connector

How to connect the main AC power with the DP2K-E series projector projector?

1. Remove the right side cover of the projector. See procedure "Removal of the right side cover", page 125.

2. Make sure that the projector is switched off. Position the power switch in the ’0’ (OFF) position (1).

3. Connect the female side of the power cord with the power input socket of the projector (2).

Image 5-5

4. Connect the male side of the power cord to the local power net.

5. Install the right side cover of the projector. See procedure "Installation of the right side cover", page 130.

R5906693 DP2K-E SERIES 19/06/2015

Summary of Contents for DP2K-E series




































































































































































Search results

Summary of Contents for DP2K-E series

Reviews:

Brands by name

Popular brands

Barco DP2K-E series, User And Installation Manual

Search results

Summary of Contents for DP2K-E series

Reviews:

Brands by name

Popular brands