manualshive.com logo in svg

Barco DP2K-E series, User And Installation Manual, Page: 44 / 163

Share
Download
Barco DP2K-E series User And Installation Manual Download Page 44

7. Input & Communication

7.1

Introduction

General

The Input & Communication side of the DP2K-E series projector consists of a Local Keypad integrated into the projector housing
and a card cage with three slots. The top side of the projector is equipped with a tail light which re

fl

ects the status of the projector.

The projector card cage is equipped with an ICMP. See illustration below. Note that all information about the ICMP is gathered into
one separated chapter: "ICMP", page 47.

1

2

3

5

4

Image 7-1
1

Projector status light.

2

Power ON/OFF switch.

3

Local keypad.

4

Barco Cinema Controller.

5

ICMP.

C

AUTION

:

A unit may only be removed from the card cage by quali

fi

ed service personnel. Removing one of

the boards (except for the Cinema Controller) will result in an authorization request upon starting.

40

R5906693 DP2K-E SERIES 19/06/2015

Summary of Contents for DP2K-E series




































































































































































Reviews:

No comments