manualshive.com logo in svg

Banner Q45, Setup Manual

Share
Download
Banner Q45 Setup Manual Download Page 12

Banner Engineering Corp.

9714 Tenth Avenue North 

• 

Minneapolis, Minnesota 55441 

763-544-3164 

•

 1-888-373-6767

www.bannerengineering.com

© 2020 Banner Engineering Corp. Mpls. MN USA

217889 Rev A

To add additional doors to an occupancy monitoring system, order one of each model listed below (900 MHz or 2.4 GHz).

Sensor Pair

Indicator

Operator Interface

Sensor L Bracket

Reflectors and 

Bracket

Battery

Battery

Power Supply

900 MHz

DX80N9Q45LPDIR

TL70DXN9GRQ-

INOUTIKIT

DX80N9DSTS

SMBQ45PC

SMBRPC

BWA-

BATT-013 

C Battery

BWA-BATT-006 

AA Batteries

PSW-24-1

2.4 GHz

DX80N2Q45LPDIR

TL70DXN2GRQ-

INOUTIKIT

DX80N2DSTS

900 MHz models are more commonly used in the United States; 2.4 GHz models are required in the EU and many other countries.

Additional Mounting Options

BWA-BK-020 Magnet Mount

•  Used with the Direct Select Operator Interface or DXM Controller
•  Includes two 80-lb pull rare-earth magnet mounts 

and two #10-32 × 1 inch screw mounts 

•  Used on multiple mounting brackets 
•  31.75 mm (1.25 inch) diameter
•  No fasteners included

LMB30LP

•  Used with the TL70 Wireless Indicator Light
•  Low profile 
•  30 mm mounting hole 
•  300 series stainless steel 
•  No fasteners included

SMBAMS30RA

•  Used with the Q45 Sensor Pair; one per sensor
•  Right-angle SMBAMS series bracket
•  30 mm hole for mounting sensors
•  Articulation slots for 90°+ rotation
•  12-gauge (2.6 mm) cold-rolled steel
•  No fasteners included

Optional Accessories

Warning Indicator Segment

SG-TL70-Y

 

•  Used with the TL70 Wireless Indicator Light
•  Yellow indicator for Warning indication

View Dashboard and Set Parameters

After Banner CDS has created the site and detected the DXM Controller, click on 

Go to Dashboard

 (Go to Dashboard). The 

 (Dashboard) panel appears and indicates the metrics of the Occupancy Solution Kit. 

The data on this dashboard will include a historical indication of the Occupancy of the area and a means of updating the 
Occupancy Limit and Occupancy Warning parameters.

4

SXI-LTE-001

•  Used with DXM Controller
•  Allows for Cellular Connectivity to the Banner CDS platform

Cellular Modem

Summary of Contents for Q45













Reviews:

No comments

Brands by name

Popular brands

Load more brands