Banner L-GAGE LT7PIDQ Manual Download Page 21

Page: 21 / 24

L-GAGE

LT7 Long-Range Time-of-Flight Sensor

P/N 120244

Banner Engineering Corp.

•

Minneapolis, MN U.S.A.

www.bannerengineering.com • Tel: 763.544.3164

Accessory Mounting Brackets

SMBLT7

• Right-angle bracket

• 300 series stainless steel

• Fine-adjust accessory available (model

SMBLT7F)

SMBLT7F

• Fine-adjust accessory for model

SMBLT7

bracket;

bracket sold separately

• 304 series stainless steel

• Mounting hardware included

��

Using the Bracket and Fine-Adjust Accessory

Bolt the two accessories to the base and/or angle of the bracket as shown in the photo

above, aligning the small pins in the accessory with the small holes in the bracket.

Install the sensor on the bracket, and the bracket on the mounting surface, using the

bracket’s curved slots for rough alignment. Tighten these bolts finger-tight. Tighten or

loosen the SMBLT7F set screws to fine-adjust the sensor alignment in each axis; then

tighten all bolts.

Summary of Contents for L-GAGE LT7PIDQ

























Search results

Summary of Contents for L-GAGE LT7PIDQ

Reviews:

Brands by name

Popular brands

Banner L-GAGE LT7PIDQ, Manual

Search results

Summary of Contents for L-GAGE LT7PIDQ

Reviews:

Brands by name

Popular brands